FREE SHIPPING OVER $149.00* - Save $$ by Buying 6 or More for Jets, Filters & Fittings.

100% Australian Owned & Operated Small Family Business - No Gimmicks - No Spam

Closed Good Friday & Easter Monday

Acrylic / PVC Repair Kit - IPS Weld-On 810 Epoxy

$104.00 $110.00
Tax included Shipping calculated at checkout.

Description

IPS Weld-on 810 2-part adhesive. Great for repairs of plastic & acrylic parts under  pressure. Cures white. Great on spa cracks and holes. Simply prepare the area, fill and sand back. It can then be painted or colour-matched by paint specialist.

Can be used for many plastic repairs including:

  • Repairs & Adhering to PVC, CPVC, ABS, Styrene, Acrylic, FRP, Concrete, Clay
  • Shower Bases
  • Acrylic or fibreglass spa and pool shells
  • Other plastic parts and fittings

Two-component, high strength, low VOC reactive adhesive. Product can withstand very high pressure and is high impact resistant. Great for repairing cracks or leaky pipe valves and fittings. It has excellent gap-filling property which is ideal for fabricating fittings and joining saddles to pipe. Also good for bonding large diameter PVC and CPVC pipe and fittings.

More Info:

  • Withstands temperatures of -33°C to 93°C
  • Set Time: 1 hour
  • Cure Time: 2 hours
  • Full Strength: 24 hours

Substrates Preparation: 

Bonding surfaces must be clean and dry. If the surfaces are hard and glossy, abrading (sanding) and priming with a degreasing solvent is recommended. Chlorinated solvents, methyl ethyl ketone, acetone and/or rubbing isopropyl alcohol may be used to
remove grease and/or dirt.

Installation:

1. Assemble materials for the job: WELD-ON 810 kit, clean mixing sticks, applicators (spatula or stiff brush), sandpaper, clean wiping cloth, cleaning solvent and gloves.

2. Prepare joints by sanding to roughen mating surfaces. Wipe surfaces clean with a dry rag or solvent cleaner. Do not soften surfaces with solvent cleaner.

3. WELD-ON 810 kit has a mixing ratio of 100:13 and both components are packaged and pre-measured to this ratio. Add Component B (small container) to Component A (large container). Mix thoroughly and apply to each mating surface. Pot life and
working time is about 30 minutes at 70 °F (21 °C).

4. Assemble parts and allow squeeze out to remain as filler.

5. Allow the joined surfaces to cure undisturbed. Recommended set time is 1 hour. Recommended cure time is 2 hours to reach 80% bond strength (resin layer cures to a hard gel), 24 hours to reach near ultimate strength. The cured layer is a tough, chemical
and water resistant plastic.

Note: Warmer weather will shorten pot life and cure time. Colder weather will increase the time for both. Applying heat may speed up the cure time. When joining CPVC for service temperatures over 150 °F (65 °C), please contact WELD-ON for more information.

Repairs:

Replacing a failed joint with new material and taking greater care in the joining process is always preferred. This repair is for leaks only and ideal for area where the joint cannot be cut out. Do not use this method if the pipe has separated from the fitting.

1. Assemble materials for the job: WELD-ON 810 kit, clean mixing sticks, applicators (spatula or stiff brush), fiberglass cloth mat cut to desirable size for wrapping the leaked pipe, sandpaper or emery, clean wiping cloth, and gloves.

2. Turn off water pressure. Dry off the bonding area and abrade it well with sandpaper and wipe clean.

3. Prepare WELD-ON 810 adhesive. Add Component B (small container) to Component A (large container) and mix thoroughly.

4. Apply a generous coat of adhesive mixture to leakage and surrounding area.

5. Apply the adhesive mixture to the mating surface of fiberglass cloth. Wrap cloth around the leaked pipe. Some adhesive should squeeze up through cloth.

Note: Fiberglass cloth is recommended for added structural strength to the leaked pipe. Good bonding result is also achievable without using the cloth.

6. Apply an additional coat of WELD-ON 810 adhesive to the top surface.

7. Let cure for a minimum of 4 hours at 70 °F (21 °C). Overnight or 24-hour cure is desirable before re-pressurizing the systems

Not recommended for use on Neoprene, Delrin, PTFE, Silicone, Polypropylene, Polyethylene and other Polyolefins or joints with an interference fit.

MSDS Sheet


Payment & Security

Payment methods

  • American Express
  • Apple Pay
  • Google Pay
  • Mastercard
  • PayPal
  • Shop Pay
  • Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information. Major Credit Cards, PayPal, ApplePay, GooglePay accepted.

  • Identifying Parts

    Before making a phone call, the fastest way to identify parts is to send photos of the Front, Back, Sides along with any Measurements.

    Use the Contact Us form to upload from a Phone, Tablet or Computer.

  • Technical Support

    For Technical Queries, please use the Contact Form. Please include as much information as possible.

    We also have a range of manuals available.

    Electrical & gas work must be performed by a licensed & experienced person.

  • Heater and Spa Parts - Australia's Biggest & Fastest Shipper of Spa Parts & Pool Heaters

    About Us

    100% Australian Owned & Operated. A real, physical store, with shipping from Vic, NSW, Qld, & WA.

    We carry more stock of spa parts & pool heaters and ship faster than anyone!

    Ex-employees of the biggest manufacturers and distributors, so we know what we're talking about!